Intercom Provisioning Parameters

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Speaker Volume

audio.vol.spk

All IP intercoms

• 10 = "0dB"

• 9 = "-3dB"

  …

• 2 = "-24dB"

• 1 = "-27dB"

See all volume values.

N/A

Sets the volume level of the speaker for this intercom.

Automatic Gain Control (AGC)

audio.agc.use

All IP intercoms, except 8036

• Enabled (default) = "1"

• Disabled = "0"

N/A

Normalizes the audio level

Microphone Volume

audio.vol.mic

8036

• Low = "6dB"  

• Medium = "12dB"  

• High = "18dB"

N/A

Sets the volume level for the microphone of this intercom

UI Volume

audio.ui.vol

8036

• Mute = "0"  

• 1 = "1"  

• 2 = "2"  

• 3 = "3"  

• 4 = "4"  

• 5 = "5"  

• 6 = "6"  

• 7 = "7"  

• 8 = "8"  

• 9 = "9"  

N/A

Sets the volume of the touchscreen click sound.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Answer Inbound Call

sip.inbound

• Enabled (default) = "1"

• Disabled = "0"

N/A

Allows the doorphone to auto-answer when it receives an inbound call.

Answer Tone

phone.tone.page

• None (default)

• Tone file name

N/A

Pre-announce tone for when call is established. Use only Default, or custom uploaded file.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Outbound Ring Limit

phone.timeout.ringback

• 1 ring = "6"  

• 2 rings = "12"  

• 3 rings ="18"  

• 4 rings = "24"  

• 5 rings = "30"  

• 6 rings = "36"  

• 7 rings = "42"  

• 8 rings = "48"  

• 9 rings = "54"  

• No limit (default) = "0"

N/A

Can be used to set a limit on how long the associated speaker will ring when calling out before timing out

Ringback Tone

phone.tone.ringback

All IP intercoms

• None (default)

• Tone file name

N/A

Tone heard by the user after pressing the intercom button

Allow Call Button to End Active Call

dp.ctrl.disc

All IP intercoms, except 8036

• 0 (default) = Disabled  

• 1 = End Call  

• 2 = End and Restart Call

N/A

Allows the intercom button to end call if pressed when on a call

Play Tone to Far End Upon Answer

phone.postcall.tone

8028, 8028V, 8201, 8203

• None (default)

• Tone file name

N/A

Tone heard by the callee after answering the call from the intercom.

Cancel Ring if Door Opened

dp.ctrl.clring

8028, 8028V, 8201, 8203

• 0 (default) = Disabled  

• 1 = enabled

N/A

cancels an outbound call if it is still ringing.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

G.722 Support

audio.codec.g722

• Enabled (default) = "1"

• Disabled = "0"

N/A

Enable or disable the G.722 codec

Maximum Call Duration

phone.timeout.session

All IP intercoms

• None (default) = "0"  

• 30 seconds = "30"  

• 1 minute = "60"  

• 2 minutes = "120"  

• 3 minutes = "180"  

• 5 minutes = "300"  

• 10 minutes ="600"  

• 15 minutes = "900"  

• 20 minutes = "1200"  

• 30 minutes = "1800"  

• 45 minutes = "2700"  

• 60 minutes = "3600"

N/A

The call will disconnect according to the limit

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Door Sensor Connector

dp.io.ctrlin

• Disabled (default) = 0  

• Call Button (Dry Contact Closure) = 1

N/A

External call button can be used as an input to the door sensor connector. The external call button will function like the call button on the device.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

All IP intercoms except 8063, 8036

N/A

Multicast Type

All IP intercoms except 8063, 8036

• Regular (RTP) (default) = "0"

• Poly Group Page = "1"

• Poly Push-to-Talk = "2"

• Regular RTP + Poly Group Page = "3"

• Regular RTP + Poly Push-to-Talk = "4"

mcast.mode = 2

Select the desired multicast type

Multicast Receive Type

8063 only

• Regular (RTP) (default) = "0"

• Poly Group Page = "1"

• Poly Push-to-Talk = "2"

dc.io.doorout = "mcast or dc.io.relayout = "mcast"

Number of Zones

mcast.zones.exp

• Basic Zones Only (default) = "0"

• Basic and Expanded Zones = "1"

mcast mode = 2 mcast.polycom.mode = 0

Select “basic” zones if configuring nine or fewer multicast zones or “expanded” to configure up to 50 zones

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Poly Zone

mcast.polycom.zone

• (Default) 224.0.1.116:5001

• IP address and port number

mcast.mode = 2 mcast.polycom.mode = 1 or mcast.polycom.mode = 2

Multicast address used for poly Group Page

Poly Receiver Channels

mcast.polycom.groups

All IP intercoms, except 8063, 8036

• Numbers separated by commas Example: "mcast.rx.zones = 1,8,9"

mcast.mode = 2 mcast.polycom.mode = 1 or mcast.polycom.mode = 2

Selected groups will be monitored for incoming multicast transmissions.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Basic Receiver Zones

mcast.rx.zones

Numbers separated by commas Example: "mcast.rx.zones = 1,8,9"

mcast.mode = 2 mcast.polycom.mode = 0

Selected zones will be monitored for incoming multicast transmissions.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Door Control Relay (Relay 1)

dc.io.doorout

• Disabled = null

• Door Control Link ="link"

• Stand-Alone Mode ="sa"

• Multicast Receiver ="mcast"

N/A

The local door control relay

Door Control Password

dc.link.pwd

String

dc.io.doorout = link

The password for the door control link when used with intercoms

Stand-Alone Mode

dc.sa.mode

• Unlock after DTMF Input ="unlock-dtmf"

• Unlock Immediately Upon Ring (Do not answer call) ="unlock-ring"

• Unlock Immediately and Answer Call ="unlock-answer"

dc.io.doorout = sa

The device is connected to phone system via SIP

Aux Out Relay (Relay 2)

dc.io.relayout

• Disabled = null

• Follow Door Control ="doorctl"

• Follow Input #1= "follow-in1"

• Follow Input #2 = "follow-in2"

• Follow Input #1 & #2 = "follow-both"

• Door Alarm= "dooralarm"

• Multicast Receiver = "mcast"

N/A

Determine what events will activate the output relay.

Basic Receiver Zones

Numbers separated by commas. Example: "mcast.doorout.zones = 1,2,3,4,5,6,7,8,9"

dc.io.relayout = "mcast"

and mcast.polycom.mode = 0

The multicast zones that will activate this relay.

Numbers separated by commas. Example: "mcast.doorout.zones = 1,24,25"

Numbers separated by commas. Example: "mcast.doorout.zones = 1,24,25"

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Unlock Via Schedule

dc.sched.use

• Disabled = "0"

• Enabled = "1"

N/A

Allow the controller to unlock the door during specified times on specified days.

Unlock Time

dc.sched.start

• "HH:MM:SS"

dc.sched.use = 1

The controller will unlock the door at the specified time.

Lock Time

dc.sched.stop

• "HH:MM:SS"

dc.sched.use = 1

The controller will lock the door at the specified time.

Days to Apply Schedule

dc.sched.days

• Sunday ="1"

• Monday ="2"

• Tuesday ="3"

  …

  (eg: dc.sched.days =1,7 if you want the schedule to apply on weekends)

dc.sched.use = 1

The controller will apply the unlock schedule on the specified days.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Answer Prompt

dc.tone.prompt

• None (default)

• Tone file name

dc.io.doorout = sa dc.sa.mode = unlock-dtmf

Tone before the call starts heard on intercom

Door Unlock Tone

dc.tone.unlock

dc.io.doorout = sa dc.sa.mode = unlock-dtmf or unlock-answer

Tone that is heard on the phone when door is opened

Momentary Open Code

dc.mopen.code

Null (Default) or 1 to 4 digit number [0-9, *, or #]

dc.io.doorout = sa dc.sa.mode = unlock-dtmf

To open the gate for set duration

Duration

dc.mopen.timeout

• 1/4 second = "250"

• 1 second = "1000"

• 2 seconds = "2000"

• 3 seconds = "3000"

• 5 seconds = "5000"

• 10 seconds ="10000"

• 15 seconds = "15000"

• 20 seconds = "20000"

• 25 seconds = "25000"

• 30seconds = "30000"

dc.io.doorout = sa dc.sa.mode = unlock-dtmf, unlock-ring, or unlock-answer

The amount of time for which the door will be unlocked.

Latch Open Code

phone.dtmf.act

dc.io.doorout = sa dc.sa.mode = unlock-dtmf

1-4 digit code that can be used to unlock the door indefinitely. Leave this field blank to disable this feature

Latch Closed Code

phone.dtmf.rls

dc.io.doorout = sa dc.sa.mode = unlock-dtmf

1-4 digit code that will lock the door again when it is latched open. Leave this field blank to disable this feature.

DTMF Detection Type

phone.dtmf.src

• Auto (default) = "auto"

• RTP Telephony Event (RFC 4733) = "rtp-telev"

• RTP In-band = "rtp-inband"

• SIP INFO = "sip-info"

dc.io.doorout = sa dc.sa.mode = unlock-dtmf

Select the desired DTMF type

End call on DTMF

dc.dtmf.term

• Disabled ="0"

• Enabled = "1"

dc.io.doorout = sa dc.sa.mode = unlock-dtmf

Terminate the call 2 seconds after the door control DTMF has been received. This feature only applies to the momentary open code.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Max Door Open

dc.opalarm.maxopen

• None (deafult) = "0"

• 30 seconds = "30"

• 2 minutes = "120"

• 15 minutes = "900"

• 30 minutes = "1800"

• 60 minutes ="3600"

• 90minutes =""5400"

• 120 minutes = "7200"

dp.io.feature1 = "doorsense" or dp.io.feature2 = "doorsense"

Triggers a door alarm if the door remains open for longer than the selected threshold

Extension to Dial

dc.opalarm.dest

SIP Extension

dp.io.feature1 = "doorsense" or dp.io.feature2 = "doorsense"

Places a call and plays the alarm tone to this extension.

Alarm Tone/Pre-recorded Announcement

• None (default)

• Tone file name

dp.io.feature1 = "doorsense" or dp.io.feature2 = "doorsense"

The tone that will play when the open alarm is triggered.

Interval Between Tones (seconds)

• 0 (default)

• Value in seconds

dp.io.feature1 = "doorsense" or dp.io.feature2 = "doorsense"

The time between loops of the open alarm tone.

Maximum Alarm Duration

• None = "0"

• 30 seconds = "30"

• 1 minute = "60"

• 2 minutes = "120”

• 3 minutes = "180"

• 5 minutes (default) = "300"

• 10 minutes ="600"

• 15 minutes = "900"

• 20 minutes = "1200"

• 30 minutes = "1800"

• 45 minutes = "2700"

• 60 minutes = "3600"

dp.io.feature1 = "doorsense" or dp.io.feature2 = "doorsense"

The maximum duration of the open alarm.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

24V Output

dc.io.pwrout

• Disabled = null

• Always On = "alwayson"

• Follow Door Control ="doorctl"

N/A

option 24V power supply for door

Output Mode

dc.io.pwrmode

• Normally Open = "nrm-open"

• Normally Closed = "nrm-closed"

dc.io.pwrout=alwayson or doorctl

Ouput mode if the 24V ouput is always on

Display Auxiliary Power State on Status Page

dc.io.pwrst

• Disabled ="0"

• Enabled = "1"

N/A

Current Limit

dc.io.pwrlim

Low (200mA) ="0" High (500mA) = "1"

dc.io.pwrout = alwayson or doorctl

Set the high current limit for the 24V output. PoE+ power is required to use the high current limit.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Wiring Fault Supervision Mode

dc.tamper.svmode

• Detect Open Circuit Fault Only = "open"

• Detect Both Open Circuit & Short Circuit Faults = "twoway"

dc.in1.mode = "nrm-opensv" or "nrm-closedsv"

Determine the electrical faults to be detected by supervision.

Action

dc.tamper.action

• Play Tone via Multicast = "mcasttone"

• Make SIP Call with Tone = "siptone"

dc.in1.mode = "nrm-opensv" or "nrm-closedsv"

The action to take when a fault is detected.

Tone/Pre-recorded Announcement

dc.tamper.tone

• None (default)

• Tone file name

dc.in1.mode = "nrm-opensv" or "nrm-closedsv"

The tone to play when tampering is detected.

Tone Duration

dc.tamper.duration

• Play Once = "0"

• Play While Tamper Active = "1"

dc.in1.mode = "nrm-opensv" or "nrm-closedsv"

Allow the tone to play once or while the fault is detected.

Interval Between Tones (seconds)

dc.tamper.interval

• 0 (default)

• Non-Negative Integer

dc.in1.mode = "nrm-opensv" or "nrm-closedsv"

The amount of time between loops of the tone.

Maximum Tone Duration

dc.tamper.maxtone

• None (default) = "0"

• 5 seconds = "5"

• 15 seconds = "15"

• 30 seconds = "30"

• 1 minute = "60"

• 2 minutes = "120"

• 3 minutes = "180"

• 5 minutes = "300"

• 10 minutes ="600"

• 15 minutes = "900"

• 20 minutes = "1200"

• 30 minutes = "1800"

• 45 minutes = "2700"

• 60 minutes = "3600"

dc.in1.mode = "nrm-opensv" or "nrm-closedsv"

The maximum time before the tone is automatically cancelled.

Multicast Sender Zone

dc.tamper.zone

Numbers separated by commas Example: "mcast.relayout.zones = 1,2,3,4,5,6,7,8,9"

dc.in1.mode = "nrm-opensv" or "nrm-closedsv" and dc.tamper.action = "mcasttone"

The multicast zone where the tone will be sent.

Extension to Dial

dc.tamper.dest

• Null (default)

• String

dc.in1.mode = "nrm-opensv" or "nrm-closedsv" and dc.tamper.action = "siptone"

The phone extension to dial for the tamper announcement.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Input #1

dc.io.feature1

• Disabled = NULL

• Audio Broadcast Features = "audio"

• Door Control Features= "door"

N/A

Options for input button press

If Audio Broadcast Features selected:

• Normally Open = "nrm-open"

• Normally Open with Supervision = "nrm-opensv"

• Normally Closed = "nrm-closed"

• Normally Closed with Supervision = "nrm-closedsv"

• Algo 1202 Call Button = "callbtn"

If Door Control Features selected:

• Normally Open = "nrm-open" Normally Closed = "nrm-closed"

dc.io.feature1 = audio or door

Tone/Pre-recorded Announcement

dc.in1.tone

• None (default)

• Tone file name

dc.io.feature1 = mcasttone or dc.io.relayin1= siptone

The Tone to be played

Tone Duration

dc.in1.dur

• Play Once = 0

• Play While Held = 1

• Play Until Completion = 3

dc.io.feature1 = mcasttone

Multicast Sender Zone

dc.in1.zone

• Prority Call = 9

• All call =8

• Music = 7

• Zone 1 =1

  …

• Zone 6 = 6

dc.io.feature1 = mcasttone

The multicast zone where the announcement will be sent.

Maximum Tone Duration

dc.in1.maxtone

• None (default) = "0"

• 5 seconds = "5"

• 15 seconds = "15"

• 30 seconds = "30"

• 1 minute = "60"

• 2 minutes = "120"

• 3 minutes = "180"

• 5 minutes = "300"

• 10 minutes ="600"

• 15 minutes = "900"

• 20 minutes = "1200"

• 30 minutes = "1800"

• 45 minutes = "2700"

• 60 minutes = "3600"

dc.io..relayin1= siptone

The maximum time before the announcement is automatically cancelled.

Extension to Dial

dc.in1.dest

• Null (default)

• String

dc.io.relayin1= siptone

The number where device will call when button is pressed

Allow 2nd Button Press

dc.in1.restart

• Disabled= 0

• End and Restart Call = 1

• End Call = 2

dc.io.relayin1= siptone

Allows the same button to end the call

Allow Cancel Button to End Tone/Call

dc.in1.cancel

• Enabled = 1

• Disabled = 0

dc.io.relay1 = "siptone" and

dc.in1.mode = "callbtn

Allow the 1202 cancel button to end the call.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Network Door Controller Address

dp.netdc1.addr

IP Address

N/A

The IP address for a remote door controller.

Network Door Controller Password

dp.netdc1.pwd

String

N/A

The password for a remote door controller.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Momentary Open Code

dp.dtmf.mopen

8028, 8028V, 8201, 8203, 8039

6 (Default) or 1 to 4 digit string The code can have numbers 0-9 as well as '*' and '#'

N/A

1-4 digit code that can be used to unlock the door for a brief period of time (as set by the Duration field). Leave this field blank to disable this feature.

Duration

dp.timeout.mopen

8028, 8028V, 8201, 8203, 8039

• 1/4 second = "250"

• 1 second = "1000"

• 2 seconds = "2000"

• 3 seconds = "3000"

• 5 seconds = "5000"

• 10 seconds ="10000"

• 15 seconds = "15000"

• 20 seconds = "20000"

• 25 seconds = "25000"

• 30seconds = "30000"

N/A

The duration for which to unlock the door when the Momentary Open Code is entered.

Cancel Unlock if Door Opened

dp.ctrl.clopen

8028, 8028V, 8201, 8203, 8039

• 0 (default) = Disabled

• 1 = enabled

N/A (8201) requires a physical door sensor installed on the door and dp.io.ctrlin = 1

This option is available only when a physical sensor is installed on the door and either "Controller Input" or "Door Station Input" is set to "Door Sensor" in "Basic Settings > Input/Output

Latch Open Code

dp.dtmf.act

8028, 8028V, 8201, 8203, 8039

Null (Default)

N/A

1-4 digit code that can be used to unlock the door indefinitely. Leave this field blank to disable this feature.

Latch Closed Code

dp.dtmf.rls

8028, 8028V, 8201, 8203, 8039

Null (Default)

N/A

1-4 digit code that will lock the door again when it is latched open. Leave this field blank to disable this feature.

DTMF Detection Type

phone.dtmf.src

8028, 8028V, 8201, 8203, 8039

• Auto = "auto" (Default)

• RTP Telephony Event (RFC 4733) = "rtp-telev"

• RTP In-band = "rtp-inband"

• SIP INFO = "sip-info"

N/A

Select the desired DTMF detection type

End call on DTMF

dp.dtmf.term

8028, 8028V, 8201, 8203, 8039

• 0 (default) = Disabled

• 1 = enabled

N/A

Terminate the call 2 seconds after the door control DTMF has been received. This feature only applies to the momentary open code.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Unlock Via Schedule

dp.sched.use

8028, 8028V, 8201, 8203

• 0 (default) = Disabled

• 1 = enabled

N/A

Select a time window in which the door will remain unlocked unless locked via another door control feature.

Days to Apply Schedule

dp.sched.days

8028, 8028V, 8201, 8203

• Sunday = 1

• Monday = 2

  …

• Saturday = 7

dp.sched.use = 1

Day of week that is checked

Unlock Time

dp.sched.start

8028, 8028V, 8201, 8203

hh:mm:ss

dp.sched.use = 1

Door will unclock at specifed time

Lock Time

dp.sched.stop

8028, 8028V, 8201, 8203

hh:mm:ss

dp.sched.use = 1

Door will lock at specifed time

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Use Door Unlock Tone

dp.tone.unlock

8028, 8028V, 8201, 8203

• 0 (default) = Disabled

• 1 = enabled

N/A

Tone heard on the phone when door is unlocked

Unlock Tone

dp.tone.fn

8028, 8028V, 8201, 8203

• Default

• Tone file name

dp.tone.unlock = 1

The tone to play when the door is unlocked.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Local Door Relay

dp.io.relay

8201, 8203, 8039

• Disabled = "disabled"

• In-Use = "inuse"

• Door Control = "doorctl"

• Ringing = "ringing"

N/A

Select which events will trigger the output relay.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Controller Input

8028, 8028V

• Disabled = NULL

• Call Button (Dry Contact Closure) = "callbtn"

• Door Sensor = "doorsense"

• Manual Door Release = "doorrls"

• Door Control Lockout = "doorctllock"

N/A

Select the mode of the controller's input relay.

Door Sensor Terminal (Relay Input) Action

8201, 8203

• Disabled = "0"

• Call Button (Dry Contact Closure) = "1"

• Door Sensor = "2"

N/A

Select the mode of the device's input relay.

Controller Input Mode

dp.io.ctrlmode

8028, 8028V

• Normally Open = "nrm-open"

• Normally Closed = nrm-closed

dp.io.ctrlin != Disabled

Type of closure provided on the controller input

Input Mode

dp.io.modein

8201, 8203

• Normally Open = "nrm-open"

• Normally Closed = nrm-closed

dp.io.ctrlin != Disabled

Type of closure provided on the Relay Input

Door Station Input

dp.io.stnin

8028, 8028V

• Disabled = NULL

• Call Button (Dry Contact Closure) = "callbtn"

• Door Sensor = "doorsense

N/A

Door Station Input(Dry contact)

Door Station Input Mode

dp.io.stnmode

8028, 8028V, 8201, 8203

• Normally Open = "nrm-open"

• Normally Closed = "nrm-closed"

N/A

Type of closure provided on the Dppr station input

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Action When Door Opened

dp.doorsense.action

8028, 8028V, 8201, 8203

• Door Alarm (SIP Call) = "0"

• Play Tone via Multicast = "1"

dp.io.ctrlin = "doorsense" or dp.io.stnlin = "doorsense"

Door sensor Action when door is opened

Max Door Open

dp.opalarm.maxopen

8028, 8028V

• None (default) = "0"

• 30 seconds = "30"

• 2 minutes = "120"

• 15 minutes = "900"

• 30 minutes = "1800"

• 60 minutes = "3600"

• 90minutes ="5400"

• 120 minutes = "7200"

dp.io.ctrlin = "doorsense" or dp.io.stnlin = "doorsense"

Triggers a door alarm if the door remains open for longer than the selected threshold

Alarm Tone/Pre-recorded Announcement

dp.opalarm.tone

8028, 8028V, 8201, 8203

• None (default_

• Tone file name

dp.io.ctrlin = "doorsense" or dp.io.stnlin = "doorsense"

The tone that will play when the open alarm is triggered.

Interval Between Tones (seconds)

dp.opalarm.interval

• 0 (default)

• Value in seconds

dp.io.ctrlin = "doorsense" or dp.io.stnlin = "doorsense"

The time between loops of the open alarm tone.

Maximum Alarm Duration

dp.opalarm.maxdur

8028, 8028V, 8201, 8203

• None = "0"

• 30 seconds = "30"

• 1 minute = "60"

• 2 minutes = "120"

• 3 minutes = "180"

• 5 minutes (default)  = "300"

• 10 minutes ="600"

• 15 minutes = "900"

• 20 minutes = "1200"

• 30 minutes = "1800"

• 45 minutes = "2700"

• 60 minutes = "3600"

dp.io.ctrlin = "doorsense" or dp.io.stnlin = "doorsense"

The maximum duration of the open alarm.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Action When Call Button Pressed

dp.callbtn.action

8028, 8028V, 8201, 8203

• Make a SIP Call = "0"

• Play Tone via Multicast = "1"

N/A

Determine the action to take when the call button is pressed.

Tone/Pre-recorded Announcement

dp.callbtn.tone

8028, 8028V, 8201, 8203

• None (default)

• Tone file name

dp.cllbtn.action = "1"

The tone to play over multicast when the call button is pressed.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Multicast Mode

dp.mcast.type

8028, 8028V, 8201, 8203

• Regular (RTP) = 0

• Poly Group Page = "1"

dp.callbtn.action = "1"

The protocol used for multicast.

IP Address

dp.mcast.ip

8028, 8028V, 8201, 8203

IP address

dp.callbtn.action = "1"

The multicast IP address where the tone will be sent.

Port

dp.mcast.port

8028, 8028V, 8201, 8203

Port number

dp.callbtn.action = "1"

The port number for the multicast address.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Call Button Backlight

dp.io.led

8028, 8028V, 8201, 8203

• 0  (default)= Disabled

• 1 = enabled

N/A

LED on the door station button

Controller Output

dp.io.ctrlout

8028, 8028V

• (Default)"Disabled"

• In-Use = "inuse"

• Ring = "ring"

• Call Button Press = "callbtn"

• Door Control = "doorctl"

• Door Sensor = "doorsense"

• Door Alarm= "dooralarm"

• Follow Controller Input = "follow-ctl"

• Follow Door Station Input = "follow-stn"

N/A

Dry contact output closure on the controller

Door Station Output

dp.io.stnout

8028, 8028V

• Disabled (default) = "Disabled"

• In-Use = "inuse"

• Ring = "ring"

• Call Button Press = "callbtn"

• Door Control = "doorctl"

• Door Sensor = "doorsense"

• Door Alarm= "dooralarm"

• Follow Controller Input = "follow-ctl"

• Follow Door Station Input = "follow-stn"

N/A

Output contact closure on door station

In-Use Definition

dp.io.inuse

8028, 8028V

• Call Connected = "inuse"

• Call Ringing or Connected = "ring+inuse"

N/A

Select the desired definition of "in use"

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

24V Output

dp.io.pwrout

8028, 8028V

• Disabled (default) = "Disabled"

• Always On = "alwayson"

• Follow Door Control = "doorctl

N/A

Optional 24V power for door strike

Output Mode

dp.io.pwrmode

8028, 8028V

• "Normally Open" (default)

• "Normally Closed"

dp.io.pwrout = doorctl

Display Auxiliary Power State on Status

dp.io.pwrst

8028, 8028V

• 0 (default) = Disabled  

• 1 = enabled

N/A

Current Limit

dp.io.pwrlim

8028, 8028V

• Low (250mA) = "Low (250mA)"

• High (500mA) = "High (500mA)"

N/A

PoE+ power is required to use the high current limit.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Alarm Tone/Pre-recorded Annoucement

dp.dcalarm.tone

8028, 8028V

• Tone file name

N/A

The tone that will play if the doorstation is disconnected.

Interval Between Tones (seconds)

dp.dcalarm.interval

8028, 8028V

default =0 (value in seconds)

N/A

The interval between loops of the tone.

Maximum Alarm Duration

dp.dcalarm.maxdur

8028, 8028V

• None = "0"

• 30 seconds = "30"

• 1 minute = "60"

• 2 minutes = "120"

• 3 minutes (default) = "180"  

• 5 minutes = "300"

• 10 minutes ="600"

• 15 minutes = "900"

• 20 minutes = "1200"

• 30 minutes = "1800"

• 45 minutes = "2700"

• 60 minutes = "3600"

N/A

The maximum duration of the door controller disconnect alarm.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Internet Protocol

net.protocol

All IP intercoms

• IPv4 only (default) = "ipv4"

• IPv4 and IPv6 = "ipv4+ipv6"

N/A

Choose to use Internet Proctocol version 4 or to use IPv4 + IPv6 dual stack.

Supersede DNS provided by DHCP

net.dhcp.c.dns

• Enabled = "1"

• Disabled (default) = "0"

N/A

Enable to provide a DNS server statically instead of using the DHCP provided name servers.

DNS Servers

net.dns.servers

• Null (default)

• IP addresses separated by ',' or ' '

net.dhcp.c.dns = 1 or net.ipv4.method = static

Provide the addresses of DNS servers.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

IPv4 Method

net.ipv4.method

All IP intercoms

• Static= "static"

• DHCP (default)= "dhcp"

N/A

Set the unit to use DHCP or static IP address

IPv4 Address/Netmask

net.ipv4.address

IP address + netmask in CIDR notation E.g., 192.168.1.10/24

net.ipv4.method = static

Enter the IP address and netmask (CIDR notation)

IPv4 Gateway

net.ipv4.gateway

All IP intercoms

IP address

net.ipv4.method = static

Enter the gateway address

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

IPv6 Method

net.ipv6.method

All IP intercoms

• Static= "static"

• (Default) DHCP = "dhcp"

net.protocol = ipv4+ipv6

Set the unit to use DHCP or static IP address

IPv6 Address/Netmask

net.ipv6.address

IP address + netmask in CIDR notation E.g., 192.168.1.10/24

net.protocol = ipv4+ipv6 and net.ipv6.method = static

Enter the IP address and netmask (CIDR notation)

IPv6 Gateway

net.ipv6.gateway

All IP intercoms

IP address

net.protocol = ipv4+ipv6 and net.ipv6.method = static

Enter the gateway address

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Destination Unreachable Messages

net.icmpv6.destunreach

All IP intercoms

• Enabled (default) = "1"

• Disabled = "0"

net.protocol = ipv4+ipv6

Filters ICMPv6 Destination Unreachable Messages

Neighbor Discovery Redirect Messages

net.icmpv6.redirect

• Enabled = "1"

• Disabled (default) = "0"

net.protocol = ipv4+ipv6

Filters ICMPv6 Neighbor Discovery Redirect Messages

Anycast Echo Replies

net.icmpv6.echo

All IP intercoms

• Enabled (default) = "1"

• Disabled = "0"

net.protocol = ipv4+ipv6

Filters ICMPv6 Anycast Echo Replies

Enable Rate Limiting Outbound Messages

net.icmpv6.enablelim

All IP intercoms

• Enabled = "1"

• Disabled (default) = "0"

net.protocol = ipv4+ipv6

Limits the rate of outgoing packets.

Rate Limit (packets per second)

net.icmpv6.ratelim

Non-negative Integer

net.protocol = ipv4+ipv6 and net.icmpv6.enablelim = 1

Limits the rate of outgoing packets.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

VLAN Mode

net.vlan.use

All IP intercoms

• None = "none"

• Manual = "manual"

• Auto (default) = "auto"

N/A

Enables or Disables VLAN Tagging

VLAN ID

net.vlan.id

Number from 0 to 4094

net.vlan.use = manual

VLAN ID

VLAN Priority

net.vlan.priority

All IP intercoms

Number from 0 to 7

net.vlan.use = manual

VLAN Priority

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

802.1X Authentication

net.pnac.use

All IP intercoms

• Enabled (default)= "1"

• Disabled = "0"

N/A

Use 802.1X authentication methods

Authentication Mode

net.pnac.auth

• EAP-TLS = "EAP-TLS"

• EAP-PEAP/MSCHAPv2 = "EAP-PEAP_MSCHAPV2"

• EAP-PEAP/GTC = "EAP-PEAP_GTC"

• EAP-TTLS/EAP-MSCHAPv2 = "EAP-TTLS_EAP-MSCHAPV2"

• EAP-TTLS/EAP-GTC = "EAP-TTLS_EAP-GTC"

• EAP-TTLS/EAP-MD5 = "EAP-TTLS_EAP-MD5"

• EAP-MD5 = "EAP-MD5"

net.pnac.use = 1

Choose the 802.1X authentication mode.

Anonymous ID

net.pnac.anon

All IP intercoms

String

net.pnac.use = 1

The 802.1X anonymous ID

ID

net.pnac.id

All IP intercoms

String

net.pnac.use = 1

The 802.1X ID

Password

net.pnac.pwd

String

net.pnac.use = 1

The 802.1X password

Validate Server Certificate

net.pnac.validate

All IP intercoms

• Enabled = "1"

• Disabled (default) = "0"

net.pnac.use = 1 and net.pnac.auth ≠ EAP-MD5

Validate the autentication server against trusted certificate authorities.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

SIP (6-bit DSCP value)

net.dscp.sip

All IP intercoms

Number from 0 to 63

N/A

Provides quality of service if the DSCP protocol is supported on your network

RTP (6-bit DSCP value)

net.dscp.rtp

Number from 0 to 63

N/A

Provides quality of service if the DSCP protocol is supported on your network

RTCP (6-bit DSCP value)

net.dscp.rtcp

All IP intercoms

Number from 0 to 63

N/A

Provides quality of service if the DSCP protocol is supported on your network

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

DNS Caching Mode

net.dns.cache

All IP intercoms

• Disabled (default) = ""

• SIP = "sip"

• All = "all"

N/A

In "SIP" mode, only the results of DNS queries for SIP requests will be cached. In "All" mode, the results of all DNS queries will be cached

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Allow Weak TLS Ciphers

net.weaktls.use

Enabled (default) = "1" Disabled = "0"

N/A

Not sure what TLS ciphers are considered weak.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Device Name (Hostname)

admin.devname

String

N/A

Name to identify the device in the Algo Network Device Locator Tool

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Network Log Protocol

log.protocol

• UDP (default)  = "udp"

• TCP = "tcp"

• TLS = "tls"

"log.method = network" or "log.method = both"

Transport layer protocol used for syslog packets.

Log Server 2

log.server2

IP address

"log.method = network" or "log.method = both"

Address for Syslog server on the network

Log Server 3

log.server3

IP address

"log.method = network" or "log.method = both"

Address for Syslog server on the network

Log Server 4

log.server4

IP address

"log.method = network" or "log.method = both"

Address for Syslog server on the network

Log Additional Events

log.add.use

• Enabled (default)= "1"

• Disabled = "0"

N/A

Writes some additional logs at the notice level. Available logs are set in parameter log.add.events.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

SNMPv3 Authentication Protocol

net.srv.snmp.auth

• None (default) = "none"

• MD5 = "MD5"

• SHA = "SHA"

• SHA-512 = "SHA-512"

• SHA-384 = "SHA-384"

• SHA-256 = "SHA-256"

• SHA-224 = "SHA-224"

net.srv.snmp = 1 and net.srv.snmp.security = 1

The community string used for SNMP. If left blank, the default string "public" will be used.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

RESTful API

admin.web.api

8028, 8028V, 8201, 8203. 8063

• Enabled = "1"

• Disabled (default) = "0"

N/A

RestFul API

Authentication Method

api.auth.basic

• Standard ="0"

• Basic ="1"

• None ="-1"

admin.web.api = 1

Type of authentication

RESTful API Password

api.admin.pwd

admin.web.api = 1 and (admin.auth.basic = 0 or admin.auth.basic = 1)

Password for authentication

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

PoE Power Detection

admin.poe.mode

8028, 8028V, 8063

• Automatic (Recommended) (default)= "auto"

• Force PoE+ = "forced"

N/A

Use the "Force PoE+" option only when connected to a PoE+ power injector capable of providing 600mA, that does not automatically negotiate its power capabilities. Incorrect use of this setting may cause the device to reboot if the power source is not capable of delivering the selected power.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Security Token

ifmc.scenario.auth

ifmc.scenario.use = 1

Enter the API security token

Include Location

ifmc.scenario.location

• Enabled (default)= "1"

• Disabled = "0"

ifmc.scenario.use = 1

Enable a location if desirred

Site ID

ifmc.scenario.site

ifmc.scenario.use = 1 and ifmc.scenario.location = 1

Enter a Site ID

Building ID

ifmc.scenario.building

ifmc.scenario.use = 1 and ifmc.scenario.location = 1

Enter a building ID

Floor ID

ifmc.scenario.floor

ifmc.scenario.use = 1 and ifmc.scenario.location = 1

Enter a floor ID

Zone ID

ifmc.scenario.zone

ifmc.scenario.use = 1 and ifmc.scenario.location = 1

Enter a Zone ID

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Microsoft Teams Support

admin.teams.use

All IP intercoms, except 8039 and 8036

• Enabled = "1"

• Disabled (default) = "0"

Teams SIP Gateway

Enable Teams support

SIP Gateway Region

admin.teams.region

Americas (North & South America) = "http://noam.ipp.sdg.teams.microsoft.com" EMEA (Europe, the Middle East & Africa) = "http://apac.ipp.sdg.teams.microsoft.com"

admin.teams.use=1

Region your Microsoft account belong to

Number of Accounts

admin.teams.num

1 to 10

admin.teams.use=1

Choose the number of sip extensions to provision. A separate Teams account is need for each extension.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Account ID

iot.tenant

iot.use=1

Account ID from the ADMP portal

Allow Configuration File Sync

iot.sync.conf

• Enabled = "1"

• Disabled (default) = "0"

iot.use=1

This feature allows ADMP to query and display settings stored on the device.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Timezone

admin.timezone

(Default) UTC Accepted values are spelled exactly like the options viewable in the dropdown box via the web interface. For more details please contact Algo Support. E.g, US/Eastern = "US/Eastern"

N/A

Select the timezone

NTP Time Server 1

net.time1

IP address or domain name

N/A

Set the primary NTP server

NTP Time Server 2

net.time2

IP address or domain name

N/A

Set a backup NTP server

NTP Time Server 3

net.time3

IP address or domain name

N/A

Set a backup NTP server

NTP Time Server 4

net.time4

IP address or domain name

N/A

Set a backup NTP server

Supersede NTP provided by DHCP

net.dhcp.c.ntp

• Enabled = "1"

• Disabled (default) = "0"

N/A

By default, if an NTP Server address is provided via DHCP Option 42, it will be used instead of the NTP servers listed above. Enable this option to ignore DHCP Option 42.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Provisioning Mode

prov.use

• Enabled (default) = "1"

• Disabled = "0"

N/A

Enable or disable provisioning

Server Method

prov.server.method

• Auto (DHCP Option 66/160/150) (default) = "auto"

• DHCP Option 66 only = "option66only"

• DHCP Option 160 only = "option160only"

• DHCP Option 150 only = "option150only"

• Static = "static"

prov.use = 1

Select the preferred server method

Static Server

prov.server.static

IP address

prov.use = 1 prov.server.method = static

Enter the static server address

Download Method

prov.download.method

TFTP (default)= "tftp"

• FTP = "ftp"

• HTTP = "http"

• HTTPS = "https"

prov.use = 1

Select the preferred download method

Validate Server Certificate

prov.download.cert

• Enabled = "1"

• Disabled (default) = "0"

prov.use = 1 prov.download.method = https

Enable or disable certificate validation for (HTTPS only)

Auth User Name

prov.auth.user

Username

prov.use = 1 prov.download.method = ftp" or "http" or "https"

Username for HTTPS provisioning

Auth Password

prov.auth.pwd

Password

prov.use = 1 prov.download.method = ftp" or "http" or "https"

Password for HTTPS provisioning

Config Download Path

prov.download.cfgpath

Folder path

prov.use = 1

Set the path for the configuration file

Firmware Download Path

prov.download.fwpath

Folder path

prov.use = 1

Set the path for the firmware files

Partial Provisioning

prov.i

• Enabled = "1"

• Disabled (default) = "0"

prov.use = 1

Enable or disable partial provisioning

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Dynamic Range Compression (DRC)

audio.drc.use

• Enabled = "1"

• Disabled (default) = "0"

N/A

Compresses the dynamic range of page audio to increase loudness

Jitter Buffer Range

audio.jc.range

• 100 milliseconds (default) = "100"

• 10 - 500 milliseconds

N/A

Removes the jitter in arriving network packets by temporarily storing them. This process corrects the inconsistent delays on the network

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Speaker Filter

audio.filter.spk

• 150Hz High-Pass = "hp150"

• 300Hz High-Pass = "hp300"

• 500Hz High-Pass = "hp500"

• None (default) ="none"

N/A

Applies a high-pass filter to the speaker output. Used to reduce audio artifacts like humming or buzzing by filtering out unwanted frequencies

Speaker Noise Filter

audio.filter.spknse

• Enabled = "1"

• Disabled (default) = "0"

N/A

Enables heavy filtering below 145Hz to reduce mains induced noise (fans)

Microphone Filter

audio.filter.mic

• 150Hz High-Pass = "hp150"

• 300Hz High-Pass = "hp300"

• 500Hz High-Pass = "hp500"

• None (default) ="none"

N/A

Applies a high-pass filter to the microphone input. Used to reduce audio artifacts like humming or buzzing by filtering out unwanted frequencies

Microphone Noise Filter

audio.filter.micnse

• Enabled = "1"

• Disabled (default) = "0"

N/A

Enables heavy filtering below 145Hz to reduce mains induced noise (fans)

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Microphone Volume

audio.vol.mic

8028, 8028V, 8201, 8203

• High = "0dB"

• Low = "-12dB"

N/A

Set the microphone as high or low

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

Outbound Call One-Way Audio (Microphone Only)

dp.silent.use

8028, 8028V, 8201, 8203

• Enabled (default)= "1"

• Disabled = "0"

N/A

Speaker is disabled for silent calling

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

SIP Transportation

sip.transp

• Auto  (default)= "auto"

• UDP = "udp"

• TCP = "tcp"

• TLS = "tls" (except for 8036, 8039, or G1 devices)

N/A

Select the transport layer protocol to use for SIP messages

SIPS Scheme

sip.sips

• Enabled = "1"

• Disabled (default) = "0"

sip.transp = tls or sip.transp = auto

Enabling SIPS Scheme requires the SIP connection from endpoint to endpoint to be secure. Only supported with TLS transportation.

Validate Server Certificate

sip.tls.validate

• Enabled = "1"

• Disabled (default) = "0"

sip.transp = tls or sip.transp = auto

Validate the SIP server against common certificate authorities. To validate against additional certificates, use the "System > File Manager" tab to upload a Base64 encoded X.509 certificate file in .pem, .cer, or .crt format to the 'certs/trusted' folder.Only supported with TLS transportation.

SIP Outbound Support (RFC 5626)

sip.outbound

• Enabled = "1"

• Disabled (default) = "0"

N/A

Enable this option to support best networking practices according to RFC 5626

Outbound Proxy

sip.obproxy

IP address or domain name:port number e.g. my_proxy.com:5070

N/A

IP address for outbound proxy

Register Period

sip.regexp

• 3600 (default)

• Number in seconds

N/A

Maximum requested period of time where the endpoint will re-register with the SIP server

Rate Limit SIP Registration

sip.regrate

• No limit (default) = "0"

• 10 per second = "100"

• 5 per second = "200"

• 1 per second = "1000"

N/A

When registering multiple SIP extensions, this will stagger the registration requests for the different extensions.

Wait for Successful Unregister

sip.unreg

• Enabled = "1"

• Disabled (default) = "0"

N/A

The device will wait for a successful SIP deregistration before making changes or rebooting. This may slow down all device configuration changes and reboots.

Name on Web Interface

Parameter

Applicable Intercoms

Permitted Values

Requirements

Description

SDP SRTP Offer

sip.srtp

• Disabled (default) = ""

• Standard = "savp"

• Optional (Non-standard AVP profile) = "avp"

N/A

Set SDP SRTP Offer

SDP SRTP Offer Crypto Suite

sip.srtp.suite

• AES_CM_128_HMAC_SHA1_80 (default) = "aes_cm_128_hmac_sha1_80"

• All Suites = ""

• For more crypto suites, refer to the web interface or contact Algo support.